What are your concepts on Tools You Need to Install a New Bathtub ?
Setting up a tub isn't exactly brain surgery, yet it does call for solid plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bath tub with a brand-new one is also a reasonably tough project. If the old bathtub is easily available, the task can move speedily; if you need to open a wall surface to remove the old bathtub and also position the brand-new tub, the task is a lot harder. In either case, the task is within a home handyman's skills, although you will certainly need a helper to vacate the old tub and also embeded in the new one. Make certain you have qualified yourself for the work as well as fit trying it. As opposed to hiring a contractor to take control of a halfway-completed task, it is much better to consider employing one prior to you begin. Possibilities are you might require a specialist plumber to make tube connections.
This short article will assist you mount a brand-new tub in your shower room if you have already bought a brand-new bathtub as well as don't need to transform the setup of your previous water supply pipelines.
Your tools and product list must comprise the following:
Planning for the Setup
Firstly, the sustaining framework provided with the bath must be fitted (if required) according to the maker's instructions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the faucet comes with a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is likewise sensible to fit a supporting plate under the faucets device to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you utilize all of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to currently be ready to be suited its final setting.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, after that the first thing you should do is disconnect the water system. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the limited accessibility that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a cloth ready for the continuing to be water that will certainly come from the pipelines. When the supply pipes have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from transforming throughout this procedure. When the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old sealing compound.
Before moving on to fit the new taps, compare the pipeline links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bath tub in the called for placement. The wood boards are handy in equally spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto 4 little points.
The next objective is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bathtub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest adaptable tap adapter to the appropriate supply pipeline by making a compression join; then do the very same for the other faucet.
Switch on the water and inspect all joints and also new pipework for leaks as well as tighten them if required. Fill up the tub as well as likewise examine the overflow electrical outlet as well as the normal electrical outlet for leaks.
Finally, fix the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the bathtub must wait till the bathtub has been used at least once as this will certainly resolve it right into its final position.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in area in between the tap and also the sink. Safeguard the tap in position with the maker offered backnut. As soon as the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular tap ports. The previous kind needs to be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, resulting in problems with moisture and also possible leakages to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes and cartridges, and also are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always fill up the bath tub with water prior to sealing, to enable the motion experienced when the tub is in use. The sealant can split rather early if you do not think about this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally quickly available on the marketplace. It is advisable to fit the floor tiles utilizing water-resistant or water-proof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our part about How to Install a Bathtub. Thanks a ton for taking a few minutes to browse our short article. Are you aware of somebody else who is intrigued by the subject? Be sure share it. I cherish reading our article about Installing A Bathtub.
Schedule And Pricing